Thermal Analysis

... In the present work ancient Greek, Hellenistic, Roman, Byzantine, post-Byzantine and later historic mortars are sampled from Fortifications, Monasteries, Churches and Historical Buildings in Rhodes, Crete, Corfu, Mount Athos and Constantinople. ...

The enormous cost of handling the challenges of flow assurance in subsea wells, flowlines, and risers, especially in deepwater applications, has necessitated a proactive approach to prevent their risk of occurrence. To ensure that transportation of the hydrocarbon is economical and efficient from the subsea wellhead to the processing units, a flow assurance heat management system is relevant in the design and planning of a fluid transport system. Consequently, the advancement of new technologies to serve the increasing need by exploring the technologically challenging and hostile subsea fields is of great importance. A comparative study on heat management systems in flowlines was conducted from the top five publishers (Elsevier, Springer, Taylor & Francis, Wiley, and Sage) based on the number of publications to determine the level of work done by researchers in the last decade, the figures from the study showed the need for scientific research in the field of active heating. Additionally, a review was implemented to ascertain the likely advantages and drawbacks of each technique, its limitations concerning field applications and then recommend suitable cost-effective technique(s). The active heating system gives the most cost-effective solution for subsea deepwater fields.

This paper discusses the thermal effect of covering the building envelope with vegetation on the microclimate in the built environment, for various climates and urban canyon geometries. A two-dimensional, prognostic, micro scale model has been used, developed for the purposes of this study. The climatic characteristics of nine cities, three urban canyon geometries, two canyon orientations and two wind directions are examined. The thermal effect of green roofs and green walls on the built environment is examined in both inside the canyon and at roof level. The effects of this temperature decrease on outdoors thermal comfort and energy savings are examined. Conclusions are drawn on whether plants on the building envelope can be used to tackle the heat island effect, depending on all these parameters taken into consideration.

Long buildings without an expansion joints are curial for thermal loads. Looking at the current scenario it seems that there is no universally accepted design approach to accommodate building movement cased by the temperature or moisture hence there is a need to assess the thermal vulnerability over seismic loading, particularly for long buildings. This paper presents the analytical comparison between thermal and seismic response for long buildings in high seismic zone. The analytical study has been performed on five different mathematical models of the building frame with a plan aspect ratios varying from 2.0 to 3.6. Equivalent static analysis based on approximate fundamental period as per IS 1893:2002 for earthquake load and thermal analysis for selected range of temperature has been carried out by using finite element software SAP. The behaviors of these long buildings are compared for earthquake and thermal loads. Results are presented in terms of response parameters such as displacement and maximum forces for selected lateral load resisting element. The results obtained from analysis indicate that the column forces are governed by thermal load for ground story and roof displacement for thermal load will be critical after a plan aspect ratio of 3.2.

Thermal analysis and the ageing studies of butyl rubber (IIR) compounds have been carried out in order to assess the effect of a silane coupling agent, Bis-(3-triethoxysilylpropyl)tetra sulphide (Si-69) on thermal and thermoxidative stability of IIR. The thermal stability of the raw rubber remained uneffected on adding Si-69, whereas the thermoxidative stability was enhanced. Similar behaviour, though to a lesser extent, has been observed for compounded rubber. The ageing properties and service life are also improved with Si-69. A suitable mechanism has been proposed.

Two original numerical techniques are developed for the finite element (FE) transient analysis of induction and permanent magnet motors operating in demanding aerospace applications. The first technique is the electromagnetic and thermal analysis weak coupling using a multiple slices 2D FE model. The advantage of the specific technique is the representation of complex actuator geometries including skewed magnets and winding ends, by using a low computational cost 2D model while taking into consideration temperature dependent material attributes. The second technique consists in the development of properly defined boundary conditions for the emulation of the cooling housing of actuators. Those boundary conditions are applied at the outer surface of the actuators in contact with the housing and eliminate the need of modeling complex 3D geometries of highly integrated actuator housings.

TUSAT is a prospective Turkish Communication Satellite designed for providing mainly data communication and broadcasting services through Ku-Band and C-Band channels. Thermal control is a vital issue in satellite design process. Therefore, all satellite subsystems and equipments should be maintained in the desired temperature range from launch to end of maneuvering life. The main function of the thermal control is to keep the equipments and the satellite structures in a given temperature range for various phases and operating modes of spacecraft during its lifetime. This paper describes the thermal control design which uses passive and active thermal control concepts. The active thermal control is based on heaters regulated by software via thermistors. Alternatively passive thermal control composes of heat pipes, multilayer insulation (MLI) blankets, radiators, paints and surface finishes maintaining temperature level of the overall carrier components within an acceptable value. The...

Stability of drugs and products has a great practical interest, which is facing to strict regulation. Thermal studies, besides the determination of the thermal properties of the investigated product allow the verification of possible interactions between the drug substances and excipients. The objective of this work was to obtain solid pre-formulates of paracetamol (PC) by spray drying (SPDR), as well as to investigate their thermal behavior. Dynamic and isotherm TG, conventional DSC and DSC-photovisual coupled methods were used to characterize the conventional and pre-formulated mixtures obtained by SPDR. The results of both DSC investigations showed slight alterations in melting temperatures, which suggests incompatibilities. The TG decomposition data of the mixtures evidenced that the dry process via SPDR leads to stability enhancement of the pre-formulated mixtures.

In this paper, we discuss the synthesis of carbon-sulfur composite (a-C:S) films by vapour phase pyrolysis of maleic anhydride and sulfur. Structural changes in the system are analysed by scanning electron microscopy and powder X-ray diffraction. Microhardness test depicts an increase in the value of hardness with an increase in sulfur concentration. Electrical conductivity of composite samples varies with sulfur concentration. Magnetoresistance (MR) measurements show a drastic increase in the value of MR for the samples prepared at < 900°C. Thermal stability of these samples is analysed by thermogravimetric analysis, which depends on the host structure and the amount of intercalated species.

The isothermal and non-isothermal degradation of a typical styrenated phthalic acid-maleic acid-propylene glycol polyester were measured. Non-isothermal and isothermal kinetic analyses were performed on the various degradation steps observed. The values of the non-isothermal and the isothermal kinetic parameters are in good agreement.